Kit consists of 2.5kg of PART A and 2.5kg of PART BÂ
Total kit volume 4.62 Litres
This product is odourless, non-toxic and formulated specifically for applying to the human body.Â
PART A is a red liquid and  PART B is a blue liquid which act as a visual aid, turning purple during the mixing process. The two components mix easily with a simple 1:1 ratio with a working time of 5-8 minutes with a cure time of 20-30 minutes @ 25°C.
Once cured the rubber is a flexible, elastic, material with outstanding release properties, a high chemical resistance and a temperature resistance of 200°C. There is practically no shrinkage (0.1%) and excellent reproduction of fine detail.
As the moulds will be thin to hold their shape when filling with the casting material an outer support will need creating whist the rubber is still in situ on the body. We recommend mod roc plaster bandages click here
One  Hand and Wrist
500g of Thixo Body Moulding  Rubber
3 x (15cm x 2.7m) Modroc  Bandages
One Arm with  Shoulder
2kg of Thixo Body Moulding  Rubber
8 x (15cm x 2.7m) Modroc  Bandages
Face
500g  of Thixo Body Moulding Rubber
3 x (15cm x 2.7m) Modroc  Bandages
Face and Partial  Neck
1kg of Thixo Body Moulding  Rubber
4 x (15cm x 2.7m) Modroc  Bandages
Front Half of Head Â
1kg of Thixo Body Moulding  Rubber
5 x (15cm x 2.7m) Modroc  Bandages
Full Head and  Neck
2kg of Thixo Body Moulding  Rubber
10 x (15cm x 2.7m) Modroc  Bandages
Chest
2kg  of Thixo Body Moulding Rubber
8 x (15cm x 2.7m) Modroc  Bandages
Full Torso Front and  Back
7kg of Thixo Body Moulding  Rubber
34 x (15cm x 2.7m) Modroc  Bandages
One  Foot
1kg of Thixo Body Moulding  Rubber
4 x (15cm x 2.7m) Modroc  Bandages
One Lower  Leg
2kg of Thixo Body Moulding  Rubber
10 x (15cm x 2.7m) Modroc  Bandages
One Full  Leg
5kg of Thixo Body Moulding  Rubber
18 x (15cm x 2.7m) Modroc  Bandages
 Properties | Units
| Â Thixo Body
|
---|
 Pot Life (25°C) | Minutes
| 5-8
|
Cure Time (25°C) | Minutes
| 20-30
|
Viscosity (25°C) | Mpa.s | 5500
|
 Density (25°C) | g/cm3 | 1.08 |
Hardness | Shore A | 20
|
 Linear Shrinkage | % | 0.1 |
Tear Strength | KN/m | 26 |
 Elongation at Break | % | 500
|
Tensile Strength | Mpa | 6
|
 Technical Data Sheet Â
 Safety Data Sheet Part A Â
 Safety Data Sheet Part B
SUITABLE FOR USE WITH:
Polyurethane resinÂ
- Epoxy resin
- Polyester resin
- Acrylic resin
- Plastisol (PVC)
- Plaster
- Cement
- Polymer Clays
- Waxes
- Soaps
- Metals with a pouring temperature below 200°C
*CURE INHIBITION*
Great care must be taken when handling and mixing all addition-cured silicone elastomer systems. All the mixing tools (vessels and spatulas) should be clean and constructed in materials which do not interfere with the curing mechanism. The cure of the rubber can be inhibited by the presence of compounds of nitrogen, sulphur, phosphorus and arsenic; organotin catalysts and PVC stabilisers; epoxy resin catalysts and even contact with materials containing these substances e.g. moulding clays, sulphur vulcanised rubbers, condensation cure silicone rubbers, onion and garlic.